|
DEMOLITION PLAN KEYED NOTES
<br />DE01 FLOOR TRENCH TO REMAIN
<br />DE02 DEMOLISH WINDOW
<br />DE03 FIXED CASEWORK ISLAND TO REMAIN
<br />DE04 CASEWORK AND FUME HOOD TO REMAIN
<br />DE05 DEMOLISH MASONRY RETAINING WALL, SEE CIVIL
<br />DE06 DEMOLISH WINDOW STOOL, WINDOW TO REMAIN
<br />DE07 DEMOLISH WINDOW AND STOOL
<br />DE08 NOT USED
<br />NOTE: NOT ALL KEYED NOTES MAY BE USED ON EACH PLAN OR BID PACK
<br />DEMOLITION GENERAL NOTES
<br />DESIGN BUILDER SHALL COORDINATE ALL DEMOLITION WORK, PHASING AND
<br />SEQUENCING WITH THE OWNER. ANY INFORMATION REGARDING SEQUENCING
<br />PROVIDED IN THESE DOCUMENTS IS FOR ARCHITECT - OWNER PLANNING
<br />PURPOSES ONLY, UNLESS NOTED OTHERWISE.
<br />DESIGN BUILDER SHALL BE RESPONSIBLE FOR COORDINATING WITH ALL
<br />TRADES FOR THE DEMOLITION WORK REQUIRED FOR THIS PROJECT.
<br />WHERE PARTITIONS ARE INDICATED TO BE REMOVED, REMOVE PARTITION
<br />ALONG WITH ALL ITEMS CONTAINED WITHIN, INCLUDING DOORS, FRAMES,
<br />HARDWARE, SIDELIGHTS, WINDOWS, MECHANICAL AND ELECTRICAL
<br />EQUIPMENT, ETC. TO STRUCTURE ABOVE, UNLESS NOTED OTHERWISE.
<br />WHERE FLOOR FINISH IS INDICATED TO BE DEMOLISHED, REMOVE FINISH TO
<br />FLOOR SLAB AS REQUIRED AND PREPARE SLAB SURFACE FOR SCHEDULED
<br />FINISHES WITHIN AREA TO BE REMODELED, UNLESS NOTED OTHERWISE. SEE
<br />FINISH SCHEDULE FOR EXISTING FLOOR FINISHES TO REMAIN UNDISTURBED.
<br />WHERE CEILING IS INDICATED TO BE DEMOLISHED, REMOVE CEILING
<br />SUSPENSION SYSTEM ALONG WITH ALL ASSOCIATED MECHANICAL AND
<br />ELECTRICAL ITEMS, UNLESS NOTED OTHERWISE. SEE MECHANICAL AND
<br />ELECTRICAL DRAWINGS FOR EXTENT OF CONDUIT, PIPING AND DUCTWORK
<br />DEMOLITION WITHIN AREA TO BE REMODELED.
<br />WHERE INDICATED, REMOVE ALL WALL/PARTITION EXISTING FINISHES AND
<br />PREPARE THE SURFACES FOR SCHEDULED FINISHES, SEE FINISH SCHEDULE
<br />FOR FINISHES.
<br />ALL DISTURBED AREAS, WALLS, PARTITIONS, FLOORS, ETC, DAMAGED BY
<br />DEMOLITION WORK SHALL BE PATCHED TO MATCH ADJACENT AREA.
<br />OWNER RESERVES THE RIGHT OF FIRST REFUSAL OF ALL SALVAGED ITEMS
<br />SUCH AS: DOORS, LIGHT FIXTURES, PLUMBING FIXTURES ETC.
<br />SALVAGED ITEMS SCHEDULED FOR REUSE SHALL BE CLEANED, RESTORED
<br />AND/OR REFINISHED TO LIKE NEW CONDITION, UNLESS NOTED OTHERWISE.
<br />DO NOT REMOVE ANY EXISTING STRUCTURAL SUPPORT MEMBERS SUCH AS
<br />COLUMNS, BEAMS, JOISTS, LOAD-BEARING PARTITIONS ETC, UNTIL ADEQUATE
<br />PERMANENT OR TEMPORARY SUPPORT IS IN PLACE. ALL EXISTING
<br />STRUCTURAL MEMBERS SHALL BE ADEQUATELY PROTECTED, COORDINATE
<br />WITH STRUCTURAL ENGINEER.
<br />SEE STRUCTURAL, DESIGN-BUILD MECHANICAL AND DESIGN-BUILD
<br />ELECTRICAL DRAWINGS FOR RELATED DEMOLITION AND PREP WORK.
<br />WALL AND CEILING MOUNTED ITEMS SHOWN DASHED, SUCH AS WALL
<br />CABINETS, SHELVING, PROJECTION SCREENS ETC, SHALL BE REMOVED,
<br />UNLESS NOTED OTHERWISE.
<br />WITHIN ALL EXISTING ROOMS/SPACES RECEIVING SCHEDULED FLOOR, OR
<br />WALL, OR CEILING FINISHES, REMOVE ALL EXISTING FLOOR, OR WALL, OR
<br />CEILING FINISHES DOWN TO THE SUBSTRATE. INCLUDE THE REMOVAL OF ALL
<br />ITEMS LOCATED WITHIN THE EXISTING FINISH REMOVALS U.N.O. PATCH AND
<br />PREP ALL SUBSTRATES TO RECEIVE SCHEDULED FINISHES. FOR ADDITIONAL
<br />INFORMATION, SEE KEYNOTED ITEMS, FINISH PLANS AND/OR SCHEDULES,
<br />STRUCTURAL, MECHANICAL AND ELECTRICAL.
<br />Revised 08-23-2016
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />7.
<br />8.
<br />9.
<br />10.
<br />11.
<br />12.
<br />13.
<br />A
<br />DEMOLITION SYMBOLS LEGEND
<br />PARTITION OR
<br />WALL TO BE
<br />DEMOLISHED
<br />PARTITION OR
<br />WALL TO REMAIN
<br />DOOR, FRAME AND
<br />HARDWARE TO BE
<br />DEMOLISHED
<br />DOOR, FRAME AND
<br />HARDWARE TO
<br />REMAIN
<br />EXISTING
<br />GRIDLINE
<br />NEW GRIDLINE
<br />NOTE: NOT ALL SYMBOLS MAY BE USED ON EACH PLAN
<br />Revised 08-23-2016
<br />A
<br />DE01 KEYNOTE
<br />ALL DASHED LINES INDICATE AN ITEM
<br />TO BE REMOVED, UNLESS NOTED OTHERWISE
<br />101
<br />PR1
<br />101B
<br />101A
<br />8'-0"
<br />M100
<br />OFFICE
<br />100'-0"
<br />FLOOR PLAN SYMBOLS LEGEND
<br />WALL
<br />EXISTING
<br />WALL TO
<br />REMAIN
<br />EQUIPMENT
<br />NUMBER
<br />WORKING POINT
<br />INTERIOR SECTION
<br />REFERENCE TAG
<br />EXTERIOR
<br />SECTION
<br />REFERENCE TAG
<br />EXTERIOR
<br />ELEVATION
<br />REFERENCE TAG
<br />INTERIOR
<br />ELEVATION
<br />REFERENCE TAG
<br />PLAN
<br />DETAIL
<br />REFERENCE
<br />TAG
<br />KEYNOTE
<br />GROMMET
<br />REVISION
<br />TAG
<br />CENTERLINE
<br />NEW GRIDLINE
<br />REVISION
<br />CLOUD
<br />FLOOR
<br />ELEVATION
<br />ROOM NAME
<br />AND NUMBER
<br />EXTENDED
<br />DIMENSION
<br />LINE, NOMINAL
<br />DIMENSION LINE
<br />NOMINAL
<br />INTERIOR
<br />BORROWED
<br />LIGHT
<br />EXISTING DOOR
<br />AND FRAME TO
<br />REMAIN
<br />DOOR
<br />WALL TAGA3
<br />D
<br />A
<br />A
<br />5101A
<br />6051A 2A
<br />620
<br />1A
<br />500
<br />1A
<br />500
<br />1A
<br />8'-0"
<br />FL01
<br />CL
<br />EXISTING
<br />GRIDLINE
<br />Revised 08-23-2016
<br />FLOOR AND ENLARGED PLAN KEYED NOTES
<br />NOTE: NOT ALL KEYED NOTES MAY BE USED ON EACH PLAN OR BID PACK
<br />FL01 ACCESSIBLE FUME HOOD, SINK, OR WORKSTATION.
<br />FL02 SLOTTED METAL CHANNEL FRAMING, SEE REFLECTED CEILING PLANS FOR
<br />LOCATIONS. INCLUDE WEIGHT CAPACITY PER LINEAR FOOT IN SUBMITTAL
<br />FL03 LASER IN USE SIGN AND LIGHT, SEE ELECTRICAL
<br />FL04 SNORKEL EXHAUST, SEE MECHANICAL
<br />FL05 NOT USED
<br />FL08 FIRE DEPARTMENT CONNECTION, SEE DESIGN-BUILD FIRE SUPPRESSION
<br />FL06 2" CONSTRUCTION EXPANSION JOINT
<br />FL07 PROVIDE RECESSED SHELVING, SEE ELEVATION FOR MORE
<br />INFORMATION.
<br />FL09 BRANDING / GRAPHICS BY OWNER
<br />9'-0" AFF
<br />ACT
<br />REFLECTED CEILING PLAN SYMBOLS LEGEND
<br />GPBD
<br />CEILING /
<br />SOFFIT
<br />ACT CEILING
<br />SYSTEM
<br />EXISTING ACT
<br />CEILING
<br />SYSTEM
<br />ACCESS PANEL
<br />CEILING
<br />ELEVATION
<br />AND FINISH
<br />MECHANICAL
<br />SUPPLY GRILLE
<br />MECHANICAL
<br />RETURN GRILLE
<br />RECESSED
<br />LIGHT
<br />FIXTURE
<br />PENDANT STRIP
<br />LIGHT FIXTURE
<br />PENDANT STRIP
<br />LIGHT FIXTURE
<br />1' X 4'
<br />LIGHT
<br />FIXTURE
<br />2' X 2'
<br />LIGHT
<br />FIXTURE
<br />2' X 4'
<br />LIGHT
<br />FIXTURE
<br />NOTE: NOT ALL SYMBOLS MAY BE USED ON EACH PLAN
<br />Revised 11-17-2016
<br />SYMBOLS LEGEND - ROOF PLAN
<br />KEYNOTE
<br />NOTE: NOT ALL SYMBOLS MAY BE USED ON EACH PLAN
<br />PRIMARY AND OVERFLOW
<br />ROOF DRAINS
<br />+4" INSULATION THICKNESS
<br />FLAT STRUCTURE WITH TAPERED
<br />INSULATION (1/4" PER FOOT SLOPE
<br />UNLESS NOTED OTHERWISE)
<br />ROOF PAVERSRP01
<br />CONSTRUCTION LIMITS
<br />CRICKET AT EQUIPMENT
<br />CRICKET BETWEEN
<br />ROOF DRAINS
<br />EQUIPMENT PLAN GENERAL NOTES
<br />EQUIPMENT SHOWN IS OWNER PROVIDED AND OWNER INSTALLED, FOR
<br />REFENCE ONLY, UNLESS OTHERWISE NOTED
<br />SEE DESIGN-BUILD MECHANICAL AND DESIGN-BUILD ELECTRICAL FOR
<br />EQUIPMENT RELATED SERVICES
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />7.
<br />8.
<br />9.
<br />10.
<br />Revised
<br />08-23-2016
<br />FINISH PLAN GENERAL NOTES
<br />Revised 08-23-2016
<br />ALL LOUVERS, VENTS, GRILLES AND OTHER MISC MECHANICAL AND
<br />ELECTRICAL DEVICES SHALL BE PAINTED TO MATCH SURFACE WHICH THEY
<br />APPEAR, UNLESS OTHERWISE NOTED.
<br />HM FRAMES TO BE PNT2, UNLESS NOTED OTHERWISE.
<br />EXISTING WALLS TO RECEIVE SCHEDULED FINISHES SHALL HAVE EXISTING
<br />FINISHES REMOVED AND SURFACES PREPARED TO RECEIVE FINISHES.
<br />ALL FLOOR FINISHES SHALL CHANGE AT CENTERLINE OF DOOR, UNLESS NOTED
<br />OTHERWISE.
<br />CONTRACTOR IS RESPONSIBLE FOR MAKING SMOOTH, FLAT JOINTS BETWEEN
<br />TRANSITIONS OF DIFFERENT FLOORING MATERIALS. FEATHER AS NEEDED
<br />UNDER FLOORING TO CREATE FLUSH TRANSITION.
<br />REFER TO SCHEDULE OF INTERIOR MATERIALS FOR FLOORING TRANSITION
<br />TYPES.
<br />REFER TO SCHEDULE OF INTERIOR MATERIALS FOR CORNER GUARD HEIGHTS.
<br />1.
<br />2.
<br />3.
<br />6.
<br />13.
<br />7.
<br />14.
<br />8.
<br />16.
<br />PAINT AND WOOD STAIN DRAW DOWNS MUST BE SUBMITTED AND APPROVED
<br />BY INTERIOR DESIGNER.
<br />9.
<br />ALL WINDOW STOOLS TO BE SSM1, UNLESS NOTED OTHERWISE. 10.
<br />NO RB AT MASONRY WALLS - TYPICAL, UNLESS NOTED OTHERWISE. 11.
<br />NO RB AT STONE WALLS - TYPICAL.12.
<br />15.
<br />REFER TO ELEV/DETAILS FOR ADDITIONAL CASEWORK AND FINISH NOTES.5.
<br />ALL COUNTERTOPS AND CASEWORK TO BE LAB CASEWORK, UNLESS NOTED
<br />OTHERWISE. REFER TO SHEET 600 AND SPEC FOR MORE INFORMATION.
<br />17.
<br />WHEN MORE THAN ONE FINISH IS LISTED IN A ROOM FINISH TAG THE FIRST
<br />FINISH LISTED IS THE PRIMARY FINISH. OTHER FINISHES LISTED ARE
<br />SPECIFICALLY CALLED OUT AND ARE SHOWN IN ELEVATION.
<br />4.
<br />INSTALL WOOD AND GRAPHIC FILM WITH GRAIN VERTICAL, UNLESS NOTED
<br />OTHERWISE.
<br />REFER TO RCP PLANS AND NOTES FOR ALL CEILING FINISHES.
<br />MAINTAIN RED BRICK MASONRY IN INTERIOR LOCATIONS WHERE POSSIBLE.
<br />18.WHERE CASEWORK IS OPEN BELOW CONTINUE SCHEDULE FLOOR AND BASE.
<br />REFLECTED CEILING PLAN GENERAL NOTES
<br />GENERAL CONTRACTOR TO COORDINATE ALL CEILING MOUNTED EQUIPMENT
<br />SUPPORT REQUIREMENTS, LOCATIONS, DIMENSIONS, ETC WITH EQUIPMENT
<br />SUPPLIER AND OWNER, PRIOR TO INSTALLATION.
<br />ALL CEILING MOUNTED ITEMS SUCH AS LIGHT FIXTURES, GRILLES, DIFFUSERS,
<br />SPEAKERS, EXIT LIGHTS, ETC SHALL BE LOCATED IN THE CENTER OF ACT/ACB
<br />PANELS, GPBD SOFFITS AND/OR PLASTER SOFFIT BAYS, UNLESS NOTED
<br />OTHERWISE. COORDINATE WITH MECHANICAL AND ELECTRICAL DRAWINGS.
<br />FINISHED GPBD SOFFITS SHALL EXTEND 1" BEYOND FACE AND EXPOSED ENDS
<br />OF WALL CABINETS, FULL-HEIGHT CABINETS, ETC UNLESS NOTED OTHERWISE.
<br />COORDINATE CABINET DIMENSIONS WITH SUPPLIER. GPBD FASCIA/SOFFIT
<br />DETAILS ARE REFERENCED FROM THE REFLECTED CEILING PLAN.
<br />SEE DESIGN-BUILD MECHANICAL DRAWINGS FOR SPRINKLER HEAD TYPES AND
<br />LOCATIONS. CENTER ALL HEADS IN ACT OR ACB UNLESS NOTED OTHERWISE.
<br />AT REMODELING WORK IN EXISTING ACT SUSPENSION SYSTEM, REMOVE
<br />EXISTING PANELS, CUT AS REQUIRED FOR CONSTRUCTION AND RE-INSTALL.
<br />REPLACE ALL DAMAGED AND EXTREMELY SOILED PANELS WITH ACT TO MATCH
<br />EXISTING.
<br />ALL GPBD CEILINGS AND SOFFITS TO BE PNT3, UNLESS NOTED OTHERWISE.
<br />Revised
<br />08-23-2016
<br />1.
<br />2.
<br />3.
<br />4.
<br />5.
<br />6.
<br />FINISH PLAN KEYED NOTES
<br />FN01 WALL FINISHES VARY, SEE ELEVATIONS FOR FURTHER INFORMATION.
<br />FN02 NO WORK IN THIS AREA, EXISTING FINISHES TO REMAIN.
<br />FN03 PATCH TO MATCH EXISTING FINISHES AS DISTURBED BY CONSTRUCTION.
<br />FN04 PROVIDE WT2, FULL HEIGHT, FULL WIDTH OF EACH WINDOW.
<br />FN05 APPLY GF1 TO INTERIOR SIDE OF GLAZING. FULL HEIGHT, FULL WIDTH OF
<br />GLAZING.
<br />FN06 BASE TO MATCH EXISTING BASE OF ROOM.
<br />FN07 MATCH ADJACENT ROOM FINISHES.
<br />FN08 REPLACE EXISTING WINDOW STOOL WITH EPOXY STOOL TO MATCH LAB
<br />CASEWORK COUNTERTOP.
<br />FN09 EXISTING DOOR PANEL AND FRAME TO BE PAINTED PNT1.
<br />NOTE: NOT ALL KEYED NOTES MAY BE USED ON EACH PLAN OR BID PACK
<br />FN10 EXISTING WINDOW TREATMENTS TO REMAIN. COORDINATE WITH OWNER.
<br />REFLECTED CEILING PLAN KEYED NOTES
<br />RC01 EXPOSED STRUCTURE AND MEP COMPONENTS, PNT3
<br />RC02 EXPOSED STRUCTURE. NO FINISH REQUIRED
<br />RC03 METAL RECESS FOR RETRACTABLE ELECTRICAL CORD REEL, SEE
<br />RC04 RETRACTABLE ELECTRICAL CORD REEL, SURFACE MOUNTED TO STRUCTURE
<br />ABOVE, SEE ELECTRICAL
<br />RC05 SLOTTED METAL CHANNEL FRAMING, VISIBLE IN ROOM, 2" CLEAR BELOW
<br />CEILING, THROUGH CEILING TO STRUCTURE ABOVE - INCLUDE WEIGHT
<br />CAPACITY PER LINEAR FOOT IN SUBMITTAL
<br />RC06 BLACKOUT CURTAIN ON TRACK
<br />RC07 SNORKEL EXHAUST DROP, SEE MECHANICAL
<br />NOTE: NOT ALL KEYED NOTES MAY BE USED ON EACH PLAN OR BID PACK
<br />/1H 640
<br />ROOF DEMOLITION AND PLAN KEYED NOTES
<br />RP04 ROOF TYPE EPDM-1A, SEE ROOF TYPES.
<br />RP05 ROOF TYPE EPDM-1B, SEE ROOF TYPES.
<br />RP02 PROVIDE CONCRETE CURB AT PENETRATIONS THROUGH CONCRETE PLANK
<br />RP06 SCREEN WALL ON STRUCTURAL STEEL
<br />RP01 DEMOLISH ROOFING AND CONCRETE PLANK FOR DUCT PENETRATION OR AHU,
<br />SEE MECHANICAL AND STRUCTURAL
<br />RP03 PATCH AND REPAIR ROOF AT DUCT PENETRATION OR AHU, SEE MECHANICAL
<br />NOTE: NOT ALL KEYED NOTES MAY BE USED ON EACH PLAN OR BID PACK
<br />CG
<br />FINISH SYMBOLS LEGEND & ABBREVIATIONS
<br />MATERIAL
<br />CHANGE
<br />LOCATION
<br />MATERIAL
<br />INSTALL
<br />DIRECTION
<br />ACCENT WALL
<br />FINISH
<br />KEYNOTE
<br />PNT
<br />VCTCPT
<br />FLOOR FINISH(ES)
<br />BASE FINISH
<br />WALL FINISH(ES)
<br />WALL
<br />PROTECTION
<br />CORNER GUARD
<br />ROOM NUMBER
<br />FN01
<br />Revised 08-23-2016
|