Laserfiche WebLink
<br />JUL-07-06 <br /> <br />02:03PM FROM-J-Craft <br /> <br /> <br />. " <br /> <br />:: . I <br /> <br />Two-Way Reversible Snow Plow - Make & Model <br /> <br />Moldboard Height <br /> <br />Moldboard smooth rolled design at wnat radius <br /> <br />Discharge Height <br /> <br />Plow Throat depth from vertical to deepest point <br /> <br />Moldboard thickness & type of steel <br /> <br />Type, size, and number of vertical reinforcement ribs <br /> <br />Adjustable outting edge angles to pavement measured <br />from roadway surface through perpedioular. back toward <br />truok. <br /> <br />State number of hookup points from moldboard to frame <br /> <br />Type and size of reinforcement of frog at either end <br /> <br />Type and size of circle frame <br /> <br />Size of single acting reversing cylinders <br /> <br />Size and type of reinforced snowflap <br /> <br />..; '? " ;~ <br /> <br />Type and size of push frame <br />Carbide outting edge (AASHTO punched) size <br /> <br />Distance beyond vertical that snow deflectors Integral with <br />moldboard extends <br /> <br />Size of adjustable snowshoes <br /> <br />Weight of plow (less hitch & hydraulics) <br /> <br />Type and number of resettable H.D. compression spring <br />trip mechanisms <br /> <br />Paint system, with type of paint <br /> <br />Warranty Detail <br /> <br />TOTAL PRICE <br /> <br />+320-398-8123 <br /> <br />T-727 P.015/020 F-504 <br /> <br />'I ; <br /> <br />'; ':V;ND:q~.T(n~~OVn:II~' ;'.;:( <br />'" ',,;"FOi.L:PWlN~,DETAltL: ~i~"~' :--- ., . <br /> <br />,.1 <br />, . <br /> <br />Falls PR1243-E1 REVERSIBLE Plow <br /> <br />43" <br /> <br />18" Radius <br /> <br />43" <br /> <br />15" <br /> <br />10 ga A607 -50 ~i-tensile steel <br />(5) 4" structural, channels (rolled) <br />. . <br /> <br />. 15" to 350 <br /> <br />Four (4)' <br /> <br />1/2" x 6" X 40" Flat Plate Note: 4" x 4" x <br />3/4" Frog Angle 15 standard <br /> <br />A-frame type, w/(2) %" thick plates <br />straddling plow pushframe, one above <br />and one below main pushframe tubing <br /> <br />3" diameter piston rods <br /> <br />(OPTIONAL) 3/8" x 12" rubber belting. <br />Nota: Flap is not a standard item <br /> <br />4" x 4" x 1/4" tubing <br /> <br />(OPTIONAL.) 5/6" x 6" Note: 1/2" x 6" <br />steel Is supplied as standard edge <br /> <br />12" <br /> <br />11" dia x 1-1/2" thick (mushroom type) <br />20S0lbs <br /> <br />2 H.D. 9/16" dia coil spring trip tilt bars, <br />are std <br /> <br />Industrial primer & (1) std enamel color <br />applied to plow. Std colors are: Earth <br />Gold, Safety Yellow. Red, Hwy Orange, <br />Black, & White. NOTE: Painting of plow is <br />included with a hitch installation, BUT <br />extra if plow is purchased separately_ <br /> <br />24 months fro .. <br /> <br />'ce" date <br /> <br /> <br />6.1 Plow push unit to fit Falls #218 or#418 modified Husting Price $873.00 <br />hitch <br /> <br />6.2 34" wide Husting Hitch in lieu of Std 29" version <br />6.3 Un-Modified version (direot lift) in lieu of Standard <br /> <br />6.0 2-WAY REV PLOW PR1243-E1 <br /> <br />Prepared by. .,J-CRAFT <br /> <br />Price $126.00 <br />Price $126.00 <br /> <br />Page 1 of3 ii <br />