2025-04-02 P & R Packet - Laserfiche WebLink

Home Browse Search

Flextread is a .375” (.95cm) thick, 2-ply performance-woven mesh with a high-quality rubber/nitrile blend. Breaking strength of 21,120 lbs. (9579kg) per 12” width. Non-marking, odorless and textured for excellent grip when wet. GATOR GRIP (TM) is a three-dimensional textured pattern exclusive to Miracle, embossed in steel to a depth of .014” to .017”. Koda XT is a polycarbonate resin designed for exterior architecture and featuring superior impact strength, formability and high-temperature resistance. G-90 galvanized indicates that a coating of .90 ounces of zinc per square foot has been applied on each surface side. A-60 Galvannealed indicates that a coating of .60 ounces of zinc per square foot alloyed with substrate steel has been applied on each surface side. Mira-Cote (TM) is a Super Durable formulation of a polyester powder coating finish that is applied to a thickness of 3-5 mil. This finish gives metal parts long term protection from chipping, fading and peeling. Miracle's finishing system washes the metal parts with detergent and etches the metal for optimum adhesion. The part is then rinsed clean with water. Next the part is coated with a non-chromic sealer and dried. The Mira-Cote powder is then applied electrostatically to the metal part. The metal parts are then baked at a high temperature to fuse a hard, smooth durable finish to the metal. Mira-Cote has an impact value of 160 in. lbs., flexibility value of 180 degree-1/4" mandrel, shore hardness value H and a crosshatch adhesion of 100%. Mira-Cote is tested in accordance with ASTM D-792, D-523, D-2794, D-1737, D-3363, D-3359 (b), B117 and D-2247. Mira-Lene (TM) is compression-molded, 3/4" thick, high density polyethylene that has been specifically formulated for optimum U.V. stability and color retention. Compression-molded products have a density of .952 g/cm3 per ASTM D1505 and tensile strength of 3900 PSI per ASTM D638. Mira-Therm2 PE is a non-toxic copolymer polyethylene coating applied to a thickness of 1/16”. Mira-Therm2 PE contains U.V. light stabilizers, anti-microbial additives and color pigments. Mira-Therm2 PE contains no orthopthalates or other banned substances. Mira-Therm2 PE is a proprietary brand of PE coating. Materials are tested in accordance with ASTM D-638, ASTM D-412, ASTM D-2240 and ASTM D-1004. Mira- Therm2 PE meets the FMVS 302 flammability rating, the requirements of California State Law and the 2008 CPSI Act. 1" pipe is GATOR GRIP embossed 14 ga., 1" pipe sized tube (1.315" OD; approx. 1-5/16" OD.) 1-1/4" pipe is 13 ga., 1-1/4" pipe sized tube (1.660" OD; approx. 1-11/16" OD.) 1-1/2" pipe is 13 ga., 1-1/2" pipe sized tube (1.900" OD; approx. 1-7/8" OD.) 5" Sch 40 pipe is 5" schedule 40 galvanized pipe (5.563" OD; approx. 5-9/16" OD.) plastic pipe plugs are injection molded polypropylene containing U.V. light stabilizers. Rockite (R) (Rotational Molded Polyethylene) is a low-density polyethylene produced from high performance, U.V. stabilized rotational molding grade resins with a comprehensive additive package. These resins are tested in accordance with ASTM testing procedures D-1505, D-1248, D- 1693(b), D- 638, D-790 and D-746. Resin's properties exhibit a balance of toughness, rigidity, environmental stress crack resistance and excellent low temperature impact performance. Wall thickness of molded components is 3/16" to 1/4". Slashproof Seat is a flexible flat single strap seat with end attachment points and an exterior surface of blue EPDM rubber. Models with chain have two segments of 4/0 straight link coil chain to suspend the swing from a swing frame header. The Slashproof seat is constructed of a 4" wide inner steel insert of type 301 stainless spring steel, 0.020" thick. The Slashproof seat is 26" long (excluding mounting triangles) x 5" wide x 5/8" thick at the front and rear leading cushion edges. The rubber molded to the steel core is 70 durometer blue EPDM. At each end, a 16 ga. galvanized steel clip 3" wide is attached by three stainless steel rivets through the clip and seat subassembly. A 3/8" diameter galvanized steel mounting triangle is encompassed by the steel clip at each end of the seat. For Model # 284-74, the lower 30" of the chain is finished in Mira-Therm2. 360 Degree Slashproof Tot Seat is a flexible seat fabricated into a configuration of a wide strap under and through the bottom, a wide strap running completely around at the top, and two (2) interconnecting straps at the front and rear of the seat for complete enclosure of the small user. The exterior surface is blue EPDM rubber. Models with chain have two segments of 4/0 straight link coil chain to suspend the swing from a swing frame header. The 360-degree tot seat is constructed of a one-piece die cut 0.020" thick, martinsitic spring steel insert with 70 durometer blue EPDM rubber, 1/4" thick, molded to the insert. The main seat strap is 5" wide, the back strap is 4" wide, and the front strap is 2" wide. The two (2) places where the straps are interconnected and form the suspension points for the seat are held by a clip and grommet system. The clip is 4" wide 16 ga. galvanized steel. There are two grommets per clip, each of which is 3/4" O.D. by 14 ga. wall galvanized steel tube, flared to securely attach the clip to the seat. The two (2) mounting triangles are secured to the seat by clips and are made from 3/8" steel round stock, formed and galvanized. For Model # 299-74, the lower 30" of the chain is finished in Mira-Therm2.