2025-04-02 P & R Packet - Laserfiche WebLink

Home Browse Search

SENSORY PANELS–BELOW DECK available for Kids’ Choice, Tots’ Choice and Tots’ Choice Expansion. These representational sensory panels, designed to enhance imagination and creative play, may be freestanding, clustered or below deck. The panel shall consist of a border plastic, plastic shape inserts and shape flanges all joined by double sided rivets. The rivets shall be aluminum. The border plastic shall be constructed of translucent colored polycarbonate. The insert plastic shall be constructed of translucent, colored and textured PETG. The shape flanges shall be constructed of 11ga. sheet steel flange. The frame shall be constructed of Gator Grip, 1" round tube and a 13ga. sheet steel flange all solid welded. The perforated panel shall be constructed of 11 ga. galvanized sheet. Each assembly shall contain Versalok Fasteners and Fastener Style A hardware. The frame and shape frames shall have a Mira-Cote finish. KIDS’ PERCH: MTII, W/WHEEL MTII, W/EXTENDED WHEEL MTII shall each consist of a curved deck extension and a curved deck enclosure designed to enhance imaginative play. Model 714-992-69 features a steering wheel fastened to the enclosure and Model 714-992-69A features a steering wheel attached to enclosure crossbars to be more easily grasped by wheelchair-bound users. The platform shall be constructed with 11 ga. steel sheet perforated with a staggered pattern of 3/8" diameter holes at 5/8" apart center-to-center. The frame shall be constructed by folding edges to form 3" tall walls and shall be supported by solid welded supports of 1/4" x 1-1/2" flat steel. The platform shall be approximately 40" long with a radius of 9-7/16". The enclosure shall consist of enclosure rails, uprights, and a center stub which shall support the bottom rail. The enclosure rails and center stub shall be constructed of 1" pipe. The crossbars shall be constructed of 1" tube. The outer uprights and mount rung shall be constructed of 1" pipe, mashed on both ends. The inner uprights shall be constructed of 3/4" x 1" oval tube. The entire assembly shall be solid welded. The mounting bracket shall be 7 ga. G-90 Galvanized sheet steel welded to the wall enclosure. The steering wheel shall be constructed of a high density blow molded polyethylene produced from high performance, U.V. stabilized resins with a comprehensive additive package. These resins shall be tested in accordance with ASTM testing procedures D-1505, D-1248, D-1693(b), D-638, D-790, and D-746. Resin's properties shall exhibit a balance of toughness, rigidity, environmental stress crack resistance, and excellent low temperature impact performance. Wall thickness shall be 1/8". The steering wheel hub cover shall be constructed of injection molded polypropylene which shall contain U.V. light stabilizers. The assembly shall contain Versalok Fasteners and Fastener Style A hardware. The platform shall be finished in Mira-Therm. The enclosure and clamps shall have a Mira-Cote finish. ROCKITE BENCH PANEL shall permit users to sit for rest, play, or group activities. Models may be installed so that the bench seat will face either the area beneath the deck or the area outside the deck system, as well as in freestanding individual or clustered arrangements. The panel shall contain view grooves for watching children at play. The bench panel shall be constructed of Rockite measuring 36” high by 40” wide by 2-1/2” thick (approximately 20” to peak) with all corners rounded, containing rotomolded flanges for field attachment of support rungs. One side of panel shall contain a 14” deep seat. Rungs shall be 1" pipe approximately 41” long. All Versalok Fasteners for deck and component attachment shall be aluminum alloy. All hardware shall be Fastener Style A. The rungs and clamps shall have a Mira-Cote finish. The panel shall have color molded in. ROCKITE BUBBLE PANEL/ROCKITE PANEL WITH HOLE/VIEW GROOVE PANEL/30 DEGREE LOOK-OUT PANEL shall be constructed of Rockite with all corners rounded. The 30-degree Look-Out panel shall have a molded in 30-degree extension. The enclosure shall consist of uprights and support bars, all constructed of 1" pipe, drilled and formed (except Tots' Choice models which shall have an enclosure consisting of a top rail of 1" tube with two tabs and two brackets of 11 ga. galvanized sheet, solid welded). The bubble shall be vacuum formed from clear polycarbonate sheet. The spherical bubble shall measure 24" in diameter and shall be attached to the panel in the factory using tamper proof screws and flat washers. The view groove panel shall have six 2" view slots evenly spaced at 5-1/4" with slant of 20 degrees from vertical. Horizontal rungs shall have a Mira-Cote finish. Rockite panels shall have color molded in. HANDHOLD FOR TRANSFER DECK, WALL ENCLOSURES, RECYCLED PLASTIC ENCLOUSRE, WIRE MESH ENCLOSURE, TREEHOUSE WALL AND ENCLOSURE WALL W/STEERING WHEEL shall be barrier assemblies. Model 714-811 Handhold for Transfer Deck, is a support rail to assist wheelchair users with access to a 12" to 18" transfer point deck. Model 714-816R Recycled Plastic Enclosure, Model 714-816 Wall Enclosure and Model 714-816-1 Wire Mesh Enclosure, are designed to be a barrier on any open side of a deck. Model 714-816-45 Wall Enclosure, Wide Side is designed to be a barrier on the hypotenuse of a right triangle (split) deck. Model 714-817 Treehouse Wall w/Seat is an enclosure with a PVC-dipped steel seat for use on 6-sided and 8-sided decks only. Model 714-900 Wall Enclosure w/Steering Wheel is designed to be a barrier designed to enhance imaginative play. The wall enclosure and wire mesh enclosure supports shall consist of a solid welded handrail assembly with top, side and bottom rails constructed of 1" pipe and spoked infill of 3/4" x 1" oval tube. Wire mesh shall be 3 ga. resistance welded at each intersection,. The steering wheel mounting bracket shall be 7 ga. G-90 Galvanized sheet steel welded to the wall enclosure. The recycled plastic enclosure shall consist of top and bottom support rails constructed of 1" pipe and uprights constructed of 3-1/2 x 2-1/2" recycled plastic timbers. The wall enclosure with seat shall comprise a top and bottom rail and end uprights constructed of 1" pipe and spoked infill of 3/4" x 1" oval tube and a seat assembly, all solid welded. The seat assembly shall comprise a frame of 1" pipe with bolting brackets of sheet 7 ga. black HR CQ and a factory-assembled 19" wide seat constructed of 11 ga. sheet, perforated with a staggered pattern of 3/8" diameter holes at 5/8" apart center- to-center. The seat surface shall be approximately 14" from the deck surface. The steering wheel shall be constructed of a high density polyethylene produced from high performance, U.V. stabilized rotational molding grade resins with a comprehensive additive package. These resins are tested in accordance with ASTM testing procedures D-1505, D-1248, D-1693(b), D638, D-790 and D-746. Resin's properties shall exhibit a balance of toughness, rigidity, environmental stress crack resistance, and excellent low temperature impact performance. Wall thickness shall be 1/8". The steering wheel hub cover shall be constructed of injection-molded polypropylene with U.V. light stabilizers. The assembly shall contain Versalok Fasteners and Fastener Style A hardware. The wall enclosure assemblies, handhold and clamps shall have a Mira-Cote finish. The seat shall be finished in Mira-Therm. The steering wheel and plastic timbers shall have color molded in. ADA SIDE STEP WITH HANDHOLDS shall comprise a single step with two handholds and shall be designed for attachment to a 1’ high deck system. The step shall be constructed of 11 ga. steel sheet with folded edges and shall be perforated with a staggered pattern of 3/8” diameter holes at 5/8” apart center-to-center. The legs each shall be 1" pipe with ends mashed and punched for field assembly to step. The handholds each shall be 1" pipe with bottom end mashed and punched for field assembly to deck. The assembly shall contain Versalok Fasteners and Fastener Style A hardware. The step shall be finished in Mira-Therm2 or Mira-Therm2 PE. The clamps, legs and handholds shall be finished in Mira-Cote.